Accelero S1 PLUS
Passive Graphics Card Cooler for AMD / NVIDIAAvailability: Out of stock
with High Compatibility - the Must-Have for
Silent Enthusiasts!
* Sold separately
In a test conducted by HW Master, the Accelero S1 PLUS reduced the GPU temperature on Sapphire HD 6570 Ultimate by 38 degrees while it was completely passive.
Equip it with an add-on fan - S1 PLUS Turbo Module, the cooling capacity of the Accelero S1 PLUS can be upgraded to 120 Watts, which is adequate enough for some of the high-end VGA cards including AMD HD 7870 and NVIDIA GTX 670.
43 °C
83 °C
Better
S1 PLUS Turbo Module is required for sufficient cooling capacity on the following VGA cards.
Nvidia GeForce GTS 250, GTS 240, GTS 150, 9800 GTX+, 9800 GTX, 9800 GT, 9600 GT, 8800 GTS 512 (G92), 7950 GT
AMD Radeon R9 270X, 270, 260X; HD 8870, 7870, 7790 GH Edition, 7850, 6870, 6850, 6790, 5850, 5830, 4870, 4850, 4830, X1900 XTX, X1800 XT
Enjoy complete silence!
40 dBA
41 dBA
Better

Heatpipes: Ø 6 mm x 4
Aluminum Fins x 32 (Thickness: 0.4 mm)
R9 270X*, R9 270*, R7 260X*, R7 260, HD 8870*, 8760, 8740, 7870*, 7850*, 7790*, 7770, 7750, 7730, 6870*, 6850*, 6790*, 6770, 6750, 6670 (LP), 6670, 6570, 5850*, 5830*, 5770, 5550 (OEM), 4870*, 4850*, 4830*, 4770, 4730, 4670, 4650, 4550, 4350 (LP), 3870, 3850, 3690, 3650, 3470, 3450, 2600 XT, 2600 Pro, 2400 XT, 2400 Pro, X1950 XTX, X1950 XT, X1950 Pro, X1950 GT, X1900 XTX*, X1900 XT, X1900 GT, X1800 XT*, X1800 XL, X1800 GTO, X1650 XT, X1650 Pro, X1600 XT, X1600 Pro, X1550, X1300 XT, X1300 Pro, X1300
NVIDIA GeForce:
GTX 650(Ti), GTS 250*, 450, 240 (OEM)*, 150 (OEM)*, GT 640, 630, 440, 340, 330, 320, 240, 220 (not LP), 210, 130 (OEM), 9800 GTX+*, 9800 GTX*, 9800 GT*, 9600 GT*, 9600 GSO, 9600 GSO 512, 9500 GT (not LP), 9400 GT (not LP), 8800 GTS 130 (OEM), 120 (OEM), 512 (G92)*, 8800 GTS (G92), 8800 GT, 8800 GS (9600GSO), 8600 GTS, 8600 GT GDDR3, 8600 GT DDR2, 8500 GT (not LP), 7950 GT*, 7900 GTX, 7900 GT, 7900 GS, 7800 GTX 512, 7800 GTX, 7800 GT, 7600 GT, 7600 GS, 7200 GS (TC)
S1 Plus Turbo Module is required. Available at s1ptm.arctic.ac for purchase.
"The reference cooler is ridiculed in the test, because 30 degrees of difference is too much."
S1 Plus: 31 C (in idle); 64 C (at load)
Stock cooler: 39 C (in idle); 74 C (at load)
"The Accelero S1 plus is designed to operate in passive mode without fan, which means no noise will be... [more]
FAQ
Compatibility with AMD R9-280(X), 7970 and 7950
The Accelero S1 Plus is compatible to the above mentioned boards if the GPU was manufactured after February 2013. Please put a ruler on top of the GPU and check whether there is a gap between the ruler and the GPU. If there is a gap, the GPU was manufactured before February 2013. In this case please use the Accelero Xtreme IV-280(X).
Pin assignments of ARCTIC VGA coolers
|
Main Cable Set
|
||
|
Pin No.
|
Color
|
Assignment
|
|
1
|
Black
|
Ground
|
|
2
|
Red
|
5-12V
|
|
3
|
Yellow
|
RPM Signal
|
|
4
|
Blue
|
PWM Signal
|
|
Sub-Cable Set
|
||
|
Pin No.
|
Color
|
Assignment
|
|
1
|
Red
|
5-12V
|
|
2
|
Black
|
Ground
|
|
3
|
Yellow
|
RPM Signal
|
Note: Please assure that the pin assignment is identical to the cooler on your graphics card. We have this far no knowledge of any graphics card manufacturer not following this standard. If it should still be the case, you can with help of a needle remove the pins from the plug and rearrange them.
How to unplug the PCI-E power connector?
How to use the 4-pin adapter?
Under what conditions do you need a 4-pin adapter?
Your graphics card
1. is using a non-standard cooler socket (e.g. 5-pin, flipped polarity) or
2. is using a passive cooler as the stock cooler
How to connect the 4-pin adapter?
The differences between 7V and 12V socket*
7V: Moderate fan speed. It gives the best balance between cooling performance and noise level. It is recommended for normal usage.
12V: Full fan speed depending on the fan design. It gives the best cooling performance and it is recommended for high duty usage.
*The fan speed is fixed regardless of the GPU's condition.
Steps
1. Ensure your PSU has spare power source and plug in the 4-pin adapter.
2. Connect your ARCTIC graphics card cooler's power plug to the preferred socket.
Please note: Make sure the connector is plugged into the corresponding socket (i.e. A 3-pin plug should be connected to a 3-pin socket and a 4-pin plug should be connected to a 4-pin socket). If the plug is connected to the wrong socket, the motor will burn immediately due to incorrect polarity.
Downloads
![]() |
Accelero S1 Plus - Height Restriction Drawing (Size: 450.7 KB) |
![]() |
Accelero S1 PLUS - Installation Manual (Czech) (Size: 3.8 MB) |
![]() |
Accelero S1 PLUS - Installation Manual (Ductch) (Size: 3.9 MB) |
![]() |
Accelero S1 PLUS - Installation Manual (English) (Size: 3.9 MB) |
![]() |
Accelero S1 PLUS - Installation Manual (French) (Size: 3.8 MB) |
![]() |
Accelero S1 PLUS - Installation Manual (German) (Size: 3.9 MB) |
![]() |
Accelero S1 PLUS - Installation Manual (Hungarian) (Size: 3.9 MB) |
![]() |
Accelero S1 PLUS - Installation Manual (Polish) (Size: 3.8 MB) |
![]() |
Accelero S1 PLUS - Installation Manual (Portuguese) (Size: 3.9 MB) |
![]() |
Accelero S1 PLUS - Installation Manual (Spanish) (Size: 3.8 MB) |
![]() |
Accelero S1 PLUS - Installation Manual (Swedish) (Size: 4.2 MB) |
![]() |
Accelero S1 PLUS - Press Release (English) (Size: 354.3 KB) |
![]() |
Accelero S1 PLUS - Press Release (German) (Size: 360.8 KB) |
![]() |
Accelero S1 PLUS - Spec Sheet (English) (Size: 1.3 MB) |
Support Form
SLI Bridge - 120mm FPC SLI Bridge
USD 5.99
Excl. Tax
|
4-pin Adapter - Cable
USD 1.99
Excl. Tax
|
S1 PLUS Turbo Module
USD 10.99
Excl. Tax
|
MX-2
USD 6.99
Excl. Tax
|
MX-4
USD 8.99
Excl. Tax
|




Xtreme Hardware
PC Update
HWMAG
Xbitlabs


Ocaholic


Pctuning

DNS








